Maintained! Second generation model of the famous P-300 series. The sharp, sharp, and exhilarating sound is alive and well. It also goes well with JBL, etc., and makes a powerful sound. You can enjoy rough sounds that cannot be experienced with current products. There are scratches and scratches on the exterior. Serial B8Y695 (Fujisawa Yukishi)
Maintenance information: 2024.5.31 Maintained (output relays, film capacitors, electrolytic capacitors, semi-fixed VR, etc. replaced. Fixed due to fixed switch. ATT disassembly and cleaning. SP switch polishing cleaning. Solder correction. Card edge contact cleaning. Increase and tighten the output terminals. ※Bias and offset check adjustment. Output audio check. (*When using MAIN & REMOTE1 speakers, be sure to connect both speakers.)
Accessories: power cord
Main specifications: 150W+150W (8Ω) W445×H160×D355mm 25kg
※6 month warranty. It is a speaker that was made for natural sound and gained popularity. There is no sense of emphasis and there is a good balance of strength between the high and low frequencies, which have a high texture, and it makes me feel the high level of musicality. There are scratches on the exterior. Serial 16400837L, 16400837R (Fujisawa Yukishi)
Maintenance information: 2024.5.31 operation confirmed
Accessories: jumper cable
Main specifications: 2-way, 2-speaker sealed, magnetic-proof type, W270 x H456 x D290 mm, 12.5 kg
Speaker cable 3.0 m/4.3 m pair end end uses a μ-conductor with unique processing applied to the PC-OCC conductor for the purpose of reproducing sound with good sharpness, and it is a cable with excellent cost performance that also achieves delicate high-frequency reproduction (Fujisawa Yukishi)
Maintenance information: 2024.5.31 continuity confirmed
Accessories: No accessories
In addition to suppressing static electricity and electromagnetic noise by adopting a 0.7 m pair titanium compound sheath, the RCA cable is heat-resistant and can also be used for car audio. It's a bit addictive (Fujisawa Yukishi)
Maintenance information: 2024.5.31 continuity confirmed
Accessories: No accessories
Maintained! NAKAMICHIN's pre-main amplifier is in stock for the first time in a while. Simple design like an English amp. The thick, energetic sound typical of Nakamichi is attractive. The exterior has dents, dullness, and small scratches on the top plate. Serial 07436 (Yonejima Satoshi)
Maintenance information: 2024.5.31 Maintained (power switch replaced. Output relay replacement. (Switch and volume contact correction)
Accessories: No accessories
Main specifications: 80W+80W (8Ω) equipped with Phonomm/MC W430 x H125 x D360 mm weight approx. 15.0 kg
Unspecified set of 4 gun type banana plugs. By making it a gun type, the depth is shortened, and it is very convenient for amplifiers placed in racks or speaker systems that don't want to take up space on the back. Dullness and oxidation are slightly noticeable. (FUJISAWA KOSHI)
Accessories: No accessories
This is an acrylic overhang gauge for LP records that is convenient for positioning cartridges. (FUJISAWA KOSHI)
Accessories: none
Main specifications: size 190 x 40 mm thickness 2 mm
This is an LP record overhang gauge that is convenient for positioning cartridges. The mirror surface makes it easy to check the cartridge position (Fujisawa Yukishi)
Accessories: No accessories
Main specifications: size 150 x 35 mm thickness 3 mm
Refreshment maintenance was carried out with attention to detail, such as all exterior painting and driver gap cleaning! You can experience a unique sound that makes you feel a hot breath in the dry sound. This time it's a combination of enclosure 828B, woofer 416-8B, driver 802-8D+511B, and network N501-8A. The outstanding vocal band and the sense of energy of the resonating horn are amazing. The exterior has been beautifully finished due to exterior repairs (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (exterior repair/full painting, saran net replacement, horn painting and butyl tape removal work, new horn receiver creation. Woofer maintenance (viscoid adjustment, terminal/vis-cleaning) driver maintenance (magnetic circuit gap cleaning/center adjustment, diaphragm screw replacement/lead disconnection repair) network maintenance (frequency characteristic check, ATT cleaning, terminal/vis-cleaning, butyl tape removal work) unit detachment, new horn stay installation processing, new wiring)
Accessories: none
Main specifications: 2 way 2 speaker unit configuration 802-8D+511b・416-8b・N501-8A・828b Dimensions W760 × H1,375 × D610 mm Weight approx. 74.0 kg
Maintained! A preamp with plenty of phono that analog users are happy with. There are 3 PHONO inputs, 5 MM cartridge loads, and a dedicated transistor is used for the MC head amplifier, so you can enjoy clear, sharp sound with a clear outline (Yoichi Murakoshi)
Maintenance information: 2024.5.29 maintenance (switch disassembly, contact polishing, contact cleaner application. Volume contact correction. Replace deteriorated parts in each circuit. PHONO circuit IC replacement display lamp replacement. (I/O pin jack polish)
Accessories: none
Main specifications: input terminal/3 phono systems (MM/MM/MC), TAPE2 system, AUX, TUNER power consumption 40W external dimensions W435 x H116 x D376 mm weight 8.5 kg
Internal and external maintenance has been applied and brushed up! JBL 40th anniversary model! A reprint model of the L101. You can enjoy the excellent sound unique to horn drivers. It has a good response and is a spacious speaker that can be matched with music of a wide range of ages. The traditional lattice net design is also attractive. There is slight discoloration on the marble (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (exterior repair/polishing/oil finish
Front and rear baffles/hakama repair/painting. Lattice repair/polishing/painting, lining replacement. Woofer edge replacement. Driver maintenance (magnetic circuit gap cleaning center adjustment). Network maintenance (frequency characteristic check, ATT cleaning).)
Accessories: lattice
Main specifications: 2 way · 2 speakers · bass reflex system · floor type frequency characteristics 35 Hz to 16,000 Hz directional characteristics (horizontal x vertical) 90 degrees x 40 degrees sound pressure level 92 dB 8 Ω allowable input 150 W crossover frequency 900 Hz enclosure volume 53.5 L W445 x H629 x D320 mm 29.1 kg/book
*One SP terminal is a replacement, so it is inexpensive. It hasn't arrived in a long time. This speaker system inherits the DS-205 design philosophy of making small-aperture woofers sound smoothly with a large capacity enclosure. You can enjoy the soft texture and loud sound. Serial 12502/12517 (Murakoshi Yoichi)
Maintenance information: 2024.5.30 maintenance (exterior cleaning/touch repair, 1 terminal replacement)
Accessories: jumper cable (external product)
Main specifications: 2-way bass reflex type 6.3 ohm 87 dB W360 x H925 x D290 mm 25 kg
Maintained! A power amplifier with a separate name for the main part of the SQ38F series. The natural, smooth sound quality with a high sense of transparency is attractive. You can relax and enjoy classical music and vocals in a natural way. The deep sound quality that cannot be expressed with the latest vacuum tube amplifiers is exceptional. There is a slight feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (vacuum tube sockets, block capacitors, electrolytic capacitors, oil capacitors, SP and RCA terminals, semi-fixed VR, fuse holder replacement. SW/VOL disassembly contacts are re-polished, and grease is applied to prevent oxidation and sulfidation. Input/output waveform confirmation, load test (8Ω load 1kHz 30W/30W), input/output waveform confirmation, sound output check performed.)
Accessories: instruction manual (copy)
Main specifications: output 30W+30W dimensions W410 x H160 x D205 mm weight 13.8 kg
Maintained by the manufacturer! Long-established Luxman compact vacuum tube type premain. The neat design and simple operability make you feel like it's a new era, but it has a sturdy finish that is warm and new, such as adopting a traditional OY type transformer. The sharp vacuum tube sound is attractive. There are line marks on the exterior and top surface, and dullness all over (Murakoshi Yoichi)
Maintenance information: 2024.5.29 manufacturer maintenance (BASS, TREBLE volume replacement. Input selector switch contact cleaning, inspection of each part, general adjustment)
Accessories: remote control, power cable, original box
Main specifications: rated output 12W+12W (6Ω), 10W+10W (8Ω/4Ω) vacuum tube ECC83 x 1, ECC82 x 2, EL84 x 4, 3 input lines, Phono (MM compatible) 1 system frequency characteristics 20 Hz to 50 kHz W297 x H162 x D258 mm 11.5 kg
A rare tone arm from RS Labs that was introduced and sold in a radio technical magazine in 1996. As with linear tracking, the tracking error is zero. The head shell part rotates freely, and the structure automatically adjusts so that tracking errors are always zero. The straight arm lowered from a high position to eliminate downforce is impressive. It is a legendary device that goes beyond the overview of traditional tone arms and reproduces analog (Murakoshi Yoichi)
Maintenance information: 2024.5.31 continuity confirmed
Accessories: original box, main weight, sub weight, hex wrench, instruction manual (English copy)
Main specifications: One-point support arm effective length 215mm
Maintained! A model based on the CDP-502ES with digital outputs and insulators added. It plays a delicate and detailed sound while maintaining the firm low frequencies and good vocal localization typical of Sony. You can see a feeling of use on the exterior, air cap marks, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.3.12 maintenance completed (grease re-coating of each part of the CD mechanism, mechanical drive belt replacement, tact switch replacement, optical system cleaning)
Accessories: none
Main specifications: Unilinear multi-bit D/A converter linear pick mechanism coaxial digital out copper-plated chassis multi-bit machine W430 × H80 × D365 mm 9.0 kg
The top model of the premain amplifier launched by AccuPhase to commemorate its 40th anniversary. Uses AAVA volume. The power amplifier section with pure Class A operation is designed to be resistant to changes in the surrounding environment. An overwhelming amount of information filled with a sense of silence and scale. It's the ultimate premain with a high degree of perfection. The exterior has a feeling of use such as dullness. Serial 16X713 (Jun Tamai)
Maintenance information: 2024.5.30 sound output confirmed
Accessories: remote control instruction manual power cord
Main specifications: 30W+30W (8Ω), 60W+60W (4Ω) frequency characteristics 20Hz to 20kHz input terminals/balance (XLR) x 2 systems, unbalance (RCA) x 5 systems. Up to 2 option boards can be added to the rear panel W465 x H191 x D428 mm 24.7 kg
It is a Schumann resonance wave (7.83 Hz) generator that increases the S/N ratio by canceling electromagnetic waves etc. generated from the entire audio equipment. To use it, power the included AC adapter from an electrical outlet and place the main unit as high as possible in the room (1 m 50 cm or more). There is no noticeable damage to the exterior (Tomonori Asae)
Main specifications: Schumann resonance wave (7.83 Hz) generator input voltage 12V W140 × D170 × H50 mm 220 g
The neat and precise design using birch wood and the beautiful tone without turbidity are unique to YAMAHA. It makes me want to play it in a tasteful way with a simple pre-main amplifier. The highly transparent, fresh sound fills the room comfortably. There are exterior, sunburn, bruises, and abrasions (Murakoshi Yoichi)
Maintenance information: 2024.5.29 sound output confirmed
Accessories: saran net
Main specifications: 2 way, 2 speakers, sealed system, bookshelf type, anti-magnetic design impedance 6 ohms, 86 dB, W205 x H382 x D285 mm, 9.5 kg/unit
The price has been reduced. 2024/5/30 sales price 128,000 yen Maintained! This is a Dynaco tubular control amplifier. It is an amplifier where you can enjoy the warm and comfortable sound unique to vintage. While the microwave feel is moderate, the nostalgic sound with an emphasis on atmosphere has a unique, hard-to-get flavor. There is a feeling of use such as rust stains on the top and sides, and rust etc. on the knobs (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (12AX7, 2000 μF electrolytic capacitor, 1 μF replacement, 1/4 W resistance added as a measure to improve switching noise, vacuum tube socket and RCA jack caulking repair, parts check including block capacitors, and operation check with AC 100 to 117 V)
Accessories: none
Main specifications: vacuum tube 12 AX7 x 4, 12 x 4 line input 5 systems phono 1 system (mm) 1 pre-out system W385 x H134 x D230 mm 7 kg
The price has been reduced. 2024/5/30 sales price 128,000 yen*It is cheap because it is in poor condition such as being scratched or the saran net peeling. It is tightly packed with a strong sealed enclosure and a high-quality unit, and the sound is moist and calm. If you drive with an amplifier with a strong drive, you can enjoy the dense mid and low frequencies. The exterior has scratches, scratches, and creases. Serial 02093/02092 (Murakoshi Yoichi)
Maintenance information: 2024.5.29 sound output confirmed
Accessories: saran net
Main specifications: impedance 8Ω output sound pressure level 85dB W220 × H390 × D255 mm 15 kg
A rare item. Technics meter unit. 3 modes can be switched. One meter can be used properly for 3 types, making it extremely easy to use. It's a rare gem just for visually enjoying sound (Oikawa Tetsuji)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: meter sensitivity 0 dBm 20 dBm switchable 3 system input switching W450 x H92 x D378 mm weight 5.3 kg
A rare item. Technics meter unit. 3 modes can be switched. One meter can be used properly for 3 types, making it extremely easy to use. It's a rare gem just for visually enjoying the sound. There are scratches and rust (Oikawa Tetsuji)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: meter sensitivity 0 dBm 20 dBm switchable 3 system input switching W450 x H92 x D378 mm weight 5.3 kg
The price has been drastically reduced. 2024/5/30 sales price 398,000 yen ※It is cheap because there are many scratches. Maintained by Taiyo International. This time it comes with a special battery BPS-2. Geoff Roland's peak stereo power amplifier. Genuine Oba Shoji product. A thorough non-resonance design using the company's traditional hard aluminum material. The high range with a sense of transparency and sharpness, the mid and low range with a sense of speed and driving power, and a vivid and satisfying sound are attractive. The exterior has scratches, line scratches, and dirt marks (Ryo Mizusaki)
Maintenance information: 2024.5.2 manufacturer maintained (BPS-2: internal cleaning, battery replacement, inspection of various parts, operation inspection. (Model2: Inspection of each part, characteristic inspection, running test)
Accessories: power cord, connection cable
Main specifications: 75W+75W (8Ω) with GAIN26/32dB changeover switch input impedance with HIGH/LOW changeover switch W445 × H133 × D362mm 21kg BPS-2: W445 × H133 × D362 mm weight 22 kg
Hi-Fi's first Trilogue series subwoofer has arrived! Not only for those using the Trilogue speaker, it also demonstrates sufficient performance as a standalone unit. This one is not compatible with spikes. The exterior has dullness and scratches. Serial 30-07-00 (Tamura Eiji)
Maintenance information: 2024.5.30 Operation confirmed
Accessories: power cable, saran net, original box
Main specifications: built-in power amplifier, 2 speakers, bass reflex, built-in power amplifier output, 200W, high frequency cutoff frequency 40/50/60hz, W380 x H540 x D650 mm, weight 45 kg
Hi-Fi's first Trilogue series subwoofer has arrived! Not only for those using the Trilogue speaker, it also demonstrates sufficient performance as a standalone unit. This is a spike specification. There are wrinkles on the exterior like wrap marks. Serial 30-07-00 (Tamura Eiji)
Maintenance information: 2024.5.30 Operation confirmed
Accessories: power cable, saran net, original box
Main specifications: built-in power amplifier, 2 speakers, bass reflex, built-in power amplifier output, 200W, high frequency cutoff frequency 40/50/60hz, W380 x H540 x D650 mm, weight 45 kg
Maintained! This is a regular imported model from Yamagiwa. A control amplifier representing the golden age of McKinn. Compared to the C28, this model has a wider range and more subtlety. The rich, glossy, and thick tone is alive and well, and it plays vintage speakers particularly well (Murakoshi Yoichi)
Maintenance information: 2024.5.28 maintenance (each SW/VOL cleaning, pin jack cleaning, lamp replacement, operation check)
Accessories: instruction manual (copy)
Main specifications: frequency characteristics 20 Hz to 20 kHz input terminals PHONO 1 · 2, AUX, TUNER, TAPE 1 · 2 W406 × H138 × D330 mm 8.6 kg
*Currently sold. A small speaker with a 16.5 cm woofer. This is a high cost performance speaker that allows you to listen to rich musical sounds that are beyond its size. The full expressive power of the mid-range is attractive. The exterior is good with no conspicuous scratches. Serial 37866 (Yonejima Satoshi)
Maintenance information: 2024.5.30 good sweep test
Accessories: saran net
Main specifications: 2 way impedance 8 ohms efficiency 90 dB playback frequency band 43 to 21,000 Hz W227 x H360 x D230 mm 7 kg
Dayton Audio's small power amplifier. Designed to be just the right size for a desktop, this is one that can be loud enough for a small speaker. It also has a headphone jack, so it can also be used as a headphone amplifier. The exterior is dull. Serial V200004300 (Tamura Eiji)
Maintenance information: 2024.5.30 Operation confirmed
Accessories: AC adapter
Main specifications: 60W+60W (4Ω) W117 x H44 x D79 mm dead weight 1.23 kg
An elaborate structural design and carefully selected materials that support the 6.0m pair of XLR cable transparent sensitivities have established the highest level of transmission quality required for audio cables. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.5.30 continuity confirmed
Accessories: none
Sony's high-end floor-type speaker. Fine and high-response high frequencies, glossy mid-range, and low frequencies with thick and firm bass lines. There is a sophisticated sense of luxury, and the high-resolution sound source can express a sense of atmosphere and realism. There is a feeling of use on the exterior due to line damage etc. (Tamai Jun)
Maintenance information: 2024.5.30 sound output confirmed
Accessories: Saran net original box
Main specifications: bass reflex 3-way 4-speaker system units used: woofer/200mm cone type x 2 midrange/130mm cone type x 1 tweeter/25mm soft dome type x 1 maximum input 200W 4Ω 88dB playback frequency band 28 to 60,000 Hz W320 x H1080 x D490 mm approx. 57 kg
Maintained. DYNACO's tubular mono power amplifiers are highly popular. The sleek, straight, and energetic sound that comes out of the small body is attractive. Combinations with Altech and JBL are a staple, and they make jazz and rock sounds powerful and full of realism. You can see a feeling of use on the exterior, dullness, rust, scratches, etc. (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (board peeling and re-soldering treatment, block capacitor 30/20/20 μF replacement, film capacitor 0.047 μF → 0.1 μF original, electrolytic capacitor 50 μF, resistance 1W → 1/2 W original replacement, BIAS readjustment/RCA jack and vacuum tube socket caulking repair. Operation check) 2016.2.27 Maintained (AC cord, cord stopper, input terminal, capacitor (47uF100V) resistor (47k, 270k, 470k, 1M) 1/2 w, replacement of 2 vacuum tubes (6550), bias adjustment)
Accessories: copy of instruction manual
Main specifications: tubular mono power amplifier using vacuum tube KT88/5AR4/6AN8A output 60W/140W W229 × H190 × D229 mm 11.5 kg
Taock SCB series sound creation board. Sandwich structure and special coating for high-density wooden boards, surface materials, and back materials centered around a honeycomb core containing cast iron powder. Spikes can be attached as an option. The unique vibration control structure greatly improves the sense of localization and sound field of sound. The exterior has scuffs, dents, felt on the bottom, etc. (Tamai Jun)
Accessories: none
Main specifications: W500×H52×D450mm 10kg
Taock SCB series sound creation board. Sandwich structure and special coating for high-density wooden boards, surface materials, and back materials centered around a honeycomb core containing cast iron powder. Spikes can be attached as an option. The unique vibration control structure greatly improves the sense of localization and sound field of sound. The exterior has scuffs, dents, felt on the bottom, etc. (Tamai Jun)
Accessories: none
Main specifications: W500×H52×D450mm 10kg
Taock SCB series sound creation board. Sandwich structure and special coating for high-density wooden boards, surface materials, and back materials centered around a honeycomb core containing cast iron powder. Spikes can be attached as an option. The unique vibration control structure greatly improves the sense of localization and sound field of sound. The exterior has scuffs, dents, felt on the bottom, etc. (Tamai Jun)
Accessories: none
Main specifications: W500×H52×D450mm 10kg
Equipped with an original needle. A rare TYPE2 from the popular V15 series. Although it is MM, the resolution is high, and the power of the low frequencies and the ease of transmission are attractive. The exterior is dull and scratched. There is no such thing as needle bends (Murakoshi Yoichi)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: none
Main specifications: mm type output 3.5 mV needle pressure 0.75 to 1.5 g dead weight 7 g
Maintained! SPU round needle type with built-in transformer. This is a shell from the Knicks era. The rich, rich SPU-like sound is attractive. The built-in transformer gives the impression that transparency and clarity have been improved. Needle cover missing. The exterior has a feeling of use such as dullness. Serial 340898 (Murakoshi Yoichi)
Maintenance information: 2024.5.29 Maintained (cantilever, damper adjustment, rubber cover replacement, cleaning)
Accessories: none
Main specifications: MC type with built-in transformer output 10 mV needle pressure 3 to 4.5 g dead weight 32 g
Self-made line selector with unknown details. It can be used with 2 input systems, 3 output systems, or 3 input systems, and 2 output systems. The exterior is well-built. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: W95 x H95 x D165 mm 778 g (actual measurement)
Technics MM Cartridges It was adopted as an accessory to the company's record player. It has a neutral, deafening sound, and is compatible with various music genres (Murakoshi Yoichi)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: none
Main specifications: mm type output voltage 3.2 mV frequency range 20 to 25 kHz needle pressure 1.75 g dead weight 6 g
Speaker cable, 1.4m pair of untreated silver-coated H-OFC conductors, double shielded, 2-core structure, Ortophone's high C/P series speaker cable. The high pitch and smoothness are attractive. There is friction and dirt on the sheath (Murakoshi Yoichi)
Maintenance information: 2024.5.29 continuity confirmed
Accessories: none
※1 bottle only. The RCA cable uses a 0.6 m 6N-7N hybrid conductor and twin core structure. The cable is thick and powerful in the mid-range, making it a great cable for vintage audio. There is slight dullness on the plug part (Murakoshi Yoichi)
Maintenance information: 2023.7.20 Continuity confirmed
Accessories: none
*The woofer edge is deformed, the center cap is dented, there is an ATT crack, and there are footprints on the top plate, etc., so it is inexpensive and is sold as is. A floor-type speaker with a porous metal cone that realizes all-metal in the entire band. From the unit to the enclosure, this is a masterpiece that incorporates technology and cost as if Otto's intention were shown. The rich, natural sound is attractive. The enclosure also has scratches, chipped corners, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: 3 way 3 speakers 8Ω 93dB W450 × H910 × D430 mm 51 kg
※Since it is for commercial use and is inexpensive, it will be handed over as is. This is a PA speaker equipped with a 38cm woofer and compression driver. Unique to PA speakers, it is a powerful and straight sounding speaker with excellent response. There is a slight feeling of use, and there is a dent in the grill on one side (Daiki Goto)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: connection cable
Main specifications: 40Hz to 20kHz 8Ω 250W 100dB input terminal speakon W466 x H648 x D386 mm 20.9 kg
※There is no problem with operation, but since it is cheap, it will be handed over as is. A unique digital amplifier technology “VL Digital” has been introduced to reproduce high-resolution sound more vividly in a PC environment, making it easy to enjoy as a desktop speaker. The color on the top plate has faded and there are dents (Oikawa Tetsuji)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: 40W+40W (4Ω) playback frequency range 50Hz to 100kHz digital IN sampling frequency 32, 44.1, 48, 96, 192 kHz/24 bit size Rch: W169 × H263 × D240 mm Lch: W169 × H263 × D215 mm Weight Rch: 6.4 kg Lch: 4.3 kg
This wooden speaker stand is ideal for small and medium speakers. The height is 44cm, making it easy to adjust the listening point. A hard urethane cushioning material is attached to the 4 corners of the top plate (Oikawa Tetsuji)
Accessories: none
Main specifications: top plate W340 x D245 mm height 440 mm bottom plate W380 x D 340 mm 5 kg